World Imports WI166389 Installation Guide download pdf

PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS,

AS YOU MAY NEED THEM AT ALATER DATE.

CAUTION – Turn off the main power at the circuit breaker before installing the

Fixture, in order to prevent possible shock.

Remove the fixture and the mounting package from the box and make sure

That no parts are missing by referencing the illustrations on the installation

Instructions.

FOR CEILING MOUNT ( Fig. 4& 5 )

Fig.4

Fig.5

Fig.6

1. A)Place the #8-32 HEX NUT(3) onto the #8-32 FXTURE MOUNTING

SCREW(4). And attach the MOUNTING SCREW（10） to the MOUNTING

RACKET(2).or universal mounting plate (whichever is provided). Do not tighten the

#8-32 HEX NUTS（3） at this time.(Fig.4)

B) If the fixture uses a single 1/8”IPS NIPPLE(4) for mounting, thread the 1/8”IPS

HEX NUT(3) onto the NIPPLE, and screw the NIPPLE into the MOUNTING

BRACKET(2).without tightening the HEX NUT(3).(Fig.5)

2. Pull the power supply wires out from the OUTLET BOX (1) and mount the

MOUNTING BRACKET (2) or the universal mounting plate to the OUTLET BOX(1),

using MOUNTING SCREWS(10).

3. Attach the power supply wire to the fixture lead wire by connecting BLACK to

BLACK(6),and WHITE to WHITE(5). Connect the FIXTURE GROUND WIRE (8) to

the SUPPLY GROUND WIRE(7) using a WIRE NUT(9)(not included).

4. Place the CANOPY(11) on the fixture over the OUTLET BOX(1) and onto the

fixture mounting screws﹝ or NIPPLE ﹞,and adjust the #8-32 fixture mounting

screws (or NIPPLE) until they protrude out from the CANOPY(11) 1/4”. Remove the

CANOPY(11) and secure the position of the fixture mounting screw ( or NIPPLE) by

tightening the HEX NUT(S)(3) against the MOUNTING BRACKET(2). Place the

CANOPY(11) back onto the fixture mounting screws,(or NIPPLE), and secure into

place using the DECORATIVE NUT(12) provided.

5. Screw in light bulbs that do not exceed the maximum wattage specified on the

fixture’s wattage rating label, into the socket(s) on the fixture.

INSTALLATION COMPLETED

FOR CHAIN-SUSPENDED CEILING MOUNT(Fig.6)

INSTALLATION INSTRUCTIONS

1. Take the parts out of the mounting package and thread a 1/8” IPS HEX NUT (5)

several turns onto each end of the NIPPLE (4). Screw the end of the NIPPLE (4)

several turns into the threaded hole of the MOUNTING BRACKET (2) but do not

tighten the HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11) and the GROUND

WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING BRACKET

(2) assembly to the OUTLET BOX (1) using the slotted holes on the MOUNTING

BRACKET (2) and the MOUNTING SCREWS (3) provided.

2. Thread the SCREW COLLAR LOOP (6) onto the end of the NIPPLE (4) that is

facing down. Place the CANOPY (15) over the OUTLET BOX (1) and adjust the

SCREW COLLAR LOOP (6) and NIPPLE (4) until the midpoint of the outside

threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the surface of

the CANOPY (15). Remove the CANOPY (15) and tighten the HEX NUTS (5)

down on the MOUNTING BRACKET (2) and the SCREW COLLAR LOOP (6).

3. Open up the end links of the CHAIN (17) and attach one end of the CHAIN (17)

onto the FIXTURE LOOP (18) (not shown) of the main section of the fixture. Slide

the THREADED RING (16) and the CANOPY (15) onto the CHAIN (17) (in that

order) and attach the other end of the CHAIN (17) to the SCREW COLLAR LOOP

(6). Close the ends of the chain links.

4. Unravel the fixture’s lead and ground wires and thread the them through every

other link of the CHAIN (17) and out through the SCREW COLLAR LOOP (6) and

NIPPLE (4) assembly, starting with the chain link attached to the FIXTURE LOOP

(18) (not shown) of the main section of the fixture.

5. Attach the power supply wires to the fixture lead wires by connecting the BLACK

SUPPLY WIRE (9) to the SMOOTH FIXTURE LEAD WIRE (or with printing on

the wire)(10) and the WHITE SUPPLY WIRE (11) to the RIBBED FIXTURE

LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the GROUND

SCREW (14) of the MOUNTING BRACKET (2). (Note: Be sure to leave an extra

3” length of the FIXTURE GROUND WIRE (7) for connection to the SUPPLY

GROUND WIRE (8)). Tighten the GROUND SCREW (14). Connect the remaining

FIXTURE GROUND WIRE (7) to the SUPPLY GROUND WIRE (8) using a WIRE

CONNECTOR (13)(not included). Place wiring and connections inside the

OUTLET BOX (1).

6. Slide the CANOPY (15) and the THREADED RING (16) up the CHAIN (17).

Place the CANOPY (15) over the OUTLET BOX (1) and secure in place by

screwing the THREADED RING (16) onto the SCREW COLLAR LOOP (6).

7. Screw light bulbs into the lamp socket. Note: Make sure they do not exceed the

maximum wattage specified on the fixture’s wattage rating label.

INSTALLATION IS NOW COMPLETED

INSTALLATION INSTRUCTIONS 1

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS,AS YOU MAY NEED THEM AT ALATER DATE.CAUTION – Turn off the main power at the circuit breaker before

Comments to this Manuals

No comments

World Imports WI166389 Installation Guide

Browse online or download Installation Guide for Unknown World Imports WI166389. World Imports WI166389 Installation Guide User Manual

Summary of Contents

Comments to this Manuals